Resini-SZUV-S9006-giga tenacity
Ifihan ti 3D Printing elo
Awọn abuda
SZUV-S9006
Ọja Apejuwe
SZUV-S9006 jẹ ẹya ABS bi SL resini ti o niga-toughnessawọn ẹya ara ẹrọ. O ti wa ni apẹrẹ fun a ri to ipinle atẹwe SLA. SZUV-S9006 le ṣee lo ni awọn ilana titunto si, awọn awoṣe imọran, awọn ẹya apejọ ati awọn apẹẹrẹ iṣẹ-ṣiṣe ni aaye ti adaṣe, iṣoogun ati awọn ile-iṣẹ eletiriki olumulo. Ile agbara awọn ẹya pẹlu SZUV-S9006 ti kọja awọn oṣu 6.5.
AGBÁRAAwọn ẹya ara ẹrọ
- Viscosity alabọde resini, irọrun atunkọ, rọrun lati nu awọn ẹya ati awọn ẹrọ
-Imudara agbara ni idaduro, imudara awọn iwọn ti awọn ẹya ni ipo ọrinrin
-nilo pọọku apa finishing
- Gun selifu aye ni ẹrọ
-Kekereisale ihamọ
AGBÁRAANFAANI
Nilo akoko ipari apakan ti o dinku, irọrun lẹhin-curing
- Kọ deede ati awọn ẹya lile ti o ga pẹlu iduroṣinṣin iwọn iwọn
-Awọn iṣakoso didara giga fun awọn ẹya simẹnti igbale
- Low isunki ati ti o dara resistance to yellowing
-Awọ funfun nla
-O dayato si machinable SLA ohun elo
Akiyesi: iwọn otutu ti szuv-s9006 ko yẹ ki o ga ju. Jọwọ lo ni isalẹ 25 ℃. Ọriniinitutu ojulumo fun lilo ati ibi ipamọ gbọdọ wa labẹ 38RH%.
Awọn ọran Ohun elo
Diẹ ninu awọn iṣẹ akanṣe mi
Ẹkọ
Ọwọ Molds
Awọn ẹya ara ẹrọ laifọwọyi
Apẹrẹ apoti
Apẹrẹ aworan
Iṣoogun
Awọn ohun-ini ti ara (Omi)
| Ifarahan | Funfun |
| iwuwo | 1.11-~ 1.15g / cm3@ 25 ℃ |
| Igi iki | 230~290cps @ 26 ℃ |
| Dp | 0.13 ~ 0.145 mm |
| Ec | 9,5 ~ 10,5 mJ / cm2 |
| Building Layer sisanra | 0.05 ~ 0.12mm |
Awọn ohun-ini Mekaniki (Ti a Ti ṣe itọju lẹhin)
| ODIwọn | ONA idanwo | IYE |
| 90-iseju UV lẹhin-ni arowoto | ||
| Lile, Shore D | ASTM D2240 | 75-85 |
| Modulu Flexural, Mpa | ASTM D790 | 2,592-2,675 |
| Agbara Flexural, Mpa | ASTM D790 | 63-70 |
| Modulu fifẹ, MPa | ASTM D 638 | 2,489-2,595 |
| Agbara fifẹ, MPa | ASTM D 638 | 36-53 |
| Elongation ni isinmi | ASTM D 638 | 15-25% |
| Iye owo ti Poisson | ASTM D 638 | 0.4-0.44 |
| Agbara ipa ti o ṣe akiyesi Izod, J/m | ASTM D256 | 45-70 |
| Ooru yiyọ kuro ni iwọn otutu, ℃ | ASTM D 648 @ 66PSI | 38-50 |
| Gilasi iyipada, Tg | DMA, E” oke | 40-54 |
| Olùsọdipúpọ ti gbona inawo | TMA (T | 90~102*E-6 |
| Ìwúwo, g/cm3 | 1.12-1.18 | |
| Dielectric Constant60 Hz | ASTM D 150-98 | 4.2-5.0 |
| Dielectric Constant 1 kHz | ASTM D 150-98 | 3.3-4.2 |
| Dielectric Constant1 MHz | ASTM D 150-98 | 3.2-4.0 |
| Dielectric StrengthkV/mm | ASTM D 1549-97a | 12.8-16.1 |
