Bottom price Printer 3d Price - Print material-high tenacity resin-9006 – Digital Manufacturing
Bottom price Printer 3d Price - Print material-high tenacity resin-9006 – Digital Manufacturing Detail:
3D Printing Materials
Introduction of 3D Printing Materials
SZUV-S9006 is an ABS like SL resin which has high-toughness features. It is designed for solid state SLA platforms. SZUV-S9006 can be applied in master patterns, concept models, assembly parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with SZUV-S9006 is over 6.5months.SZUV-S9006
-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines
-Improved strength retained, improved dimensions retention of parts in humid condition
-need minimal part finishing
-Long shelf life in machine
-Low bottom contraction
-Need less part finishing time,easier post-curing
-Buliding accurate and high tough parts with an improved dimensional stability
-High quality controls for vacuum casting parts
-Low shrink and good resistance to yellowing
-Magnificent white color
-Outstanding machinable SLA material
Physical Properties – Liquid Material
|Density||1.11-~1.15g/cm3 @ 25 ℃|
|Viscosity||230~290cps @ 26 ℃|
|Building layer thickness||0.05~0.12mm|
Mechanical Properties of Post-Cured Material
|90-minute UV post-cure|
|Hardness, Shore D||ASTM D 2240||75~85|
|Flexural modulus, Mpa||ASTM D 790||2,592-2,675|
|Flexural strength, Mpa||ASTM D 790||63- 70|
|Tensile modulus, MPa||ASTM D 638||2,489-2,595|
|Tensile strength, MPa||ASTM D 638||36-53|
|Elongation at break||ASTM D 638||15 -25%|
|Poisson`s Ratio||ASTM D 638||0.4-0.44|
|Impact strength notched Izod, J/m||ASTM D 256||45 - 70|
|Heat deflection temperature, ℃||ASTM D 648 @66PSI||38~50|
|Coefficient of thermal expension||TMA(T<Tg)||90~102*E-6|
|Dielectric Constant60 Hz||ASTM D 150-98||4.2~5.0|
|Dielectric Constant 1 kHz||ASTM D 150-98||3.3~4.2|
|Dielectric Constant1 MHz||ASTM D 150-98||3.2~4.0|
|Dielectric StrengthkV/mm||ASTM D 1549-97a||12.8~16.1|
Note: the temperature of szuv-s9006 should not be too high. Please use it below 25c.The relative humidity for use and storage must be under 38RH%.
Fire Fighting Measures
Dry powder fire extinguishing agent, alcohol resistant foam extinguishing agent, carbon dioxide, dry sand, spray water.
Fires may produce irritation and harmful gas
（3）The firemen of protective measures
Fireman should wear protective appliances (eye protection, protective clothing, mailing gas with gas mask, etc.), put out the fire in the windward.
6.Accidental Release Measures
（1）Homework personnel protective equipment
Ensure adequate ventilation, wear suitable protective clothing, make a good job in hand and eye/face protection.
（2）Environmental protection measures
Prevent products from entering the drain or open water
For a small amount of leakage, use dry sand, soil and towels absorb the residual liquid, recycling and airtight container.
For a large number of leakage, leakage of liquid can be in front of the embankment, the introduction of recycle to safe place.
（4）Secondary hazard prevention measures
Quickly remove all fire spark (ban on smoking in nearby, and the ignition).
7.Handling And Storage
（1）Operation treatment technical measures
Avoid contact with eyes, skin and clothing. Don’t inhaling mist or steam, don’t accidentally swallow, keep container tightly closed after the thorough cleaning.
（2）Partial or full ventilation
Maintain adequate ventilation
（3）Safe handling matters needing attention
No smoke, no fire
（4）Safe storage conditions
Stored in a cool, well ventilated place, away from heat, sparks and flames. Keep container tightly closed until it is put into use.
（5）packaging container and material
In the process of custody, please do not transfer to other containers. Don’t fall back to the original containers of products that will be used.
SOME OF MY PROJECTS
Product detail pictures:
Related Product Guide:
Critical Review: Materialise (MTLS) and Progress Software (PRGS) | Most Expensive 3d Printer
New Rapid Prototyping Technique for ‘Drawing’ Electrodes | Most Expensive 3d Printer
Along with the "Client-Oriented" small business philosophy, a rigorous high-quality handle system, highly developed producing machines and a powerful R&D group, we always supply high-quality products and solutions, fantastic services and aggressive costs for Bottom price Printer 3d Price - Print material-high tenacity resin-9006 – Digital Manufacturing, The product will supply to all over the world, such as: Uganda , luzern , Canada , Our products have mainly exported to south-east Asia Euro-America, and sales to all of our country. And depending on excellent quality, reasonable price, best service, we've got got good feedback from customers overseas. You are welcomed to join us for more possibilities and benefits. We welcome customers, business associations and friends from all parts of the world to contact us and seek cooperation for mutual benefits.
By Cara from Germany - 2015.09.23 17:37
The product classification is very detailed that can be very accurate to meet our demand, a professional wholesaler.
By Jean from Poland - 2016.04.18 16:45