best resin 3d printer

Short Description:

High Tenacity resin-9006 for 3D printing

3D printer materials

 


Product Detail

Composition

best resin 3d printer,
Best Resin 3d Printer,

3D Printing Materials

Resin-9006

Introduction of 3D Printing Materials

Characteristics

SZUV-S9006    

PRODUCT DESCRIPTION 

SZUV-S9006 is an ABS like SL resin which has high-toughness features. It is designed for solid state SLA platforms. SZUV-S9006 can be applied in master patterns, concept models, assembly parts and functional prototypes in the field of automotive, medical and consumer electronics industries.The parts duability building with SZUV-S9006 is over 6.5months.SZUV-S9006 

TYPICAL FEATURES

-Liquid resin`s medium viscosity, so easy recoating, easy clean parts and machines 

-Improved strength retained, improved dimensions retention of parts in humid condition 

-need minimal part finishing

-Long shelf life in machine

-Low bottom contraction 

 

TYPICAL BENEFITS

-Need less part finishing time,easier post-curing 

-Buliding accurate and high tough parts with an improved dimensional stability 

-High quality controls for vacuum casting parts

-Low shrink and good resistance to yellowing 

-Magnificent white color 

-Outstanding machinable SLA material 

High-toughness 

 Physical Properties – Liquid Material 

Appearance White
Density  1.11-~1.15g/cm3 @ 25 ℃
Viscosity   230~290cps @ 26 ℃
Dp  0.13~0.145 mm
Ec  9.5~10.5 mJ/cm2
Building layer thickness  0.05~0.12mm

 

Mechanical Properties of Post-Cured Material 

MEASUREMENT TEST METHOD  VALUE 
    90-minute UV post-cure 
Hardness, Shore D ASTM D 2240 75~85
Flexural modulus, Mpa ASTM D 790 2,592-2,675  
Flexural strength, Mpa ASTM D 790 63- 70
Tensile modulus, MPa ASTM D 638 2,489-2,595
Tensile strength, MPa ASTM D 638 36-53
Elongation at break ASTM D 638 15 -25%
Poisson`s Ratio ASTM D 638 0.4-0.44
Impact strength notched Izod, J/m  ASTM D 256 45 - 70
Heat deflection temperature, ℃  ASTM D 648 @66PSI  38~50 
Glass transition,Tg  DMA,E”peak 40~54
Coefficient of thermal expension TMA(T<Tg) 90~102*E-6
Density, g/cm3   1.12~1.18 
Dielectric Constant60 Hz ASTM D 150-98  4.2~5.0 
Dielectric Constant 1 kHz ASTM D 150-98  3.3~4.2 
Dielectric Constant1 MHz ASTM D 150-98  3.2~4.0 
Dielectric StrengthkV/mm ASTM D 1549-97a  12.8~16.1 

 Note: the temperature of szuv-s9006 should not be too high. Please use it below 25c.The relative humidity for use and storage must be under 38RH%.

 

Fire Fighting Measures

(1)extinguishant

Dry powder fire extinguishing agent, alcohol resistant foam extinguishing agent, carbon dioxide, dry sand, spray water.

(2)Special risk

Fires may produce irritation and harmful gas

(3)The firemen of protective measures

Fireman should wear protective appliances (eye protection, protective clothing, mailing gas with gas mask, etc.), put out the fire in the windward.

6.Accidental Release Measures

(1)Homework personnel protective equipment

Ensure adequate ventilation, wear suitable protective clothing, make a good job in hand and eye/face protection.

(2)Environmental protection measures

Prevent products from entering the drain or open water

(3)Cleaning method

For a small amount of leakage, use dry sand, soil and towels absorb the residual liquid, recycling and airtight container.

For a large number of leakage, leakage of liquid can be in front of the embankment, the introduction of recycle to safe place.

(4)Secondary hazard prevention measures

Quickly remove all fire spark (ban on smoking in nearby, and the ignition).

7.Handling And Storage

(1)Operation treatment technical measures

Avoid contact with eyes, skin and clothing. Don’t inhaling mist or steam, don’t accidentally swallow, keep container tightly closed after the thorough cleaning.

(2)Partial or full ventilation

Maintain adequate ventilation

(3)Safe handling matters needing attention

No smoke, no fire

(4)Safe storage conditions

Stored in a cool, well ventilated place, away from heat, sparks and flames. Keep container tightly closed until it is put into use.

(5)packaging container and material

In the process of custody, please do not transfer to other containers. Don’t fall back to the original containers of products that will be used.

Cases

SOME OF MY PROJECTS

btn12
btn7
汽车配件
包装设计
艺术设计
医疗领域

Education

Hand Molds

Auto Parts

Packaging Design

Art Design

Medical



  • Previous:
  • Next:

  • Composition/Information On Ingredients

     

    Ingredient name, CAS number

    wt%

    epoxy resinsproperty

    30-70

    acrylatesproperty

    15-50

    photoinitiatorproperty

    2-10

     

     

     

  • Related Products